Skip to content
ES App (ES) ↗
Step 4 of 5: The camera window

Dew · Step 4 of 5

Your camera’s window: a different kind of dew

In a sentence: On the telescope, the sky is in charge. On a cooled camera, its own cooling is, and that’s why the fix is different.

Here it isn’t the sky: it’s the cooler

A cooled camera takes the sensor down to −10 or −20 °C. That cold reaches the protective window in front of it by conduction, and leaves it below air temperature. The result is the same (a patch of fog), but the term that dominates here isn’t the sky, it’s the camera itself.

There’s a clear clue: QHY recommends not pointing the camera at the ground, because cold air is denser, sinks and reaches the glass. Pointing down reduces what you radiate to the sky and still makes fogging worse. And as a remedy, the same manufacturer suggests raising the sensor temperature, which would make no sense if the problem came only from above.

Heads-upOn the ZWO, QHY and Player One pages we could read, neither the sky nor radiation is mentioned when they talk about window dew: what they cite is air humidity, cold air sinking and, for condensation inside, the cooling. That doesn’t mean radiation isn’t there, only that here it isn’t what dominates.

Very few watts will do

Look at the jump: the window is solved with two to six watts, while a tube asks for fifteen or twenty. It isn’t that tube straps are oversized, it’s that they heat different things: a strap wraps a whole tube and the heat spreads around the entire circumference; the camera heater works on a disk three to six centimeters across. The lesson that holds for both: a few watts in the right place beat a lot spread thin.

And they aren’t always enough: the manufacturers themselves admit that with high humidity, or below −20 °C, that power falls short.

What manufacturers publish for the camera window
WhatPower
ZWO, external “Anti-dew” strip12 V at 0.35 A: about 4.2 W
ZWO, built-in heater (ASI071MC Pro)about 6 W
Altair, Dew Zapper (heats the housing)2 W
Player OneNo watts published; recommends setting it to 10%
ToupTekNo watts published; four levels
QHYNo watts published; its board should reach 65–70 °C at 25 °C ambient

Atik publishes nothing about a window heater. ZWO contradicts itself about which models have the built-in heater: its FAQ says every APS-C or larger camera has one, but the accessory page names only some models.

Thin glass: quick, but hard to heat

These windows are very thin. ZWO publishes the thicknesses: 1.1 mm on the 21 and 25 mm diameter windows, and 2 mm on the 32 and 60. Player One gives 2 mm on the Poseidon-C Pro.

So little glass has almost no thermal inertia, so it reaches its equilibrium temperature fast. The problem is where that equilibrium sits: below air temperature, because the cooler is pulling on it from behind.

And it has a second edge almost nobody mentions: glass that thin is hard to heat from the rim, because there’s very little cross-section to conduct heat toward the center. It fits two published facts, though neither says it in these words: QHY moved the heating board on the QHY268 by five millimeters to reduce fogging, and in a test of the Hypercam 183M the patch appears right in the center of the window below −20 °C. The explanation is ours.

If the patch is on the inside, it isn’t dew

There’s a second problem that gets confused with this one and is fixed the other way around: humidity inside the sealed camera, freezing onto the sensor. The tell: an internal patch changes between frames and doesn’t calibrate out with flats.

The usual move is to blame the desiccant, but the best-documented case we found rules that out: the owner regenerated the tablets, then replaced them with new ones, and nothing changed. What fixed it was cooling in steps: leaving the camera a few minutes at 0 °C before going down to −20 °C. ZWO blamed it on cooling too fast.

And the same works as prevention, which is far more comfortable than fixing it at midnight: capture programs have a cooling ramp, the minutes it takes to reach the temperature you asked for. If you’re not in a hurry, stretch it. ToupTek’s software ships with three minutes; we suggest ten, and with that ramp we haven’t had it again. No manufacturer publishes this: it’s our recommendation, from having been through it.

On regenerating the desiccant, every manufacturer says something different: ZWO, microwave at medium power for two minutes and fit them while still warm; Atik, oven at 200 °C (about 390 °F) (and contradicts itself between one hour and two). QHY doesn’t even supply it, because it can’t travel by air, and warns you to switch the cooling off before drying anything. Nobody publishes how often to do it: you do it when the patch shows up.

Three practical things worth knowing

  • Careful leaving it on. Users of ZWO’s ASCOM driver report that the anti-dew heater doesn’t switch off when you switch the cooling off, and keeps draining your battery without you noticing.
  • Planetary cameras don’t have one. ZWO says it plainly: the heater goes in APS-C or larger cameras. And it’s consistent: we haven’t found a single person complaining about window dew on a planetary camera, because there’s no cooler chilling it.
  • On no camera is the heater automatic by dew point. ZWO’s is a simple on or off; others have levels. You set it.