Skip to content
ES App ↗

What calibration frames do I need?

Darks, flats, dark flats, bias… how many, and do you have to redo them every night? It depends on your camera and on what you've touched. Two clicks and you'll know.

Light (your sub) Dark (capped) Flat (even light) Dark flat − − = Clean frame
The dark takes out the hot pixels and the amp glow; the flat takes out the dark corners and the dust donuts.

Your night

Your camera
Since your last session…

Darks

Flats

Dark flats

Bias

Why temperature matters

Your sensor makes signal even with no light reaching it, just from being warm: that's dark current, and it roughly doubles every 6 °C. That signal is exactly what a dark frame removes; what you can't remove is the noise it leaves behind, and that grows more slowly. Drag the temperature and watch a 5-minute dark fill up.

−10 °C

A cooled camera sits at −10 °C all night; a DSLR on a warm summer night can run past 30 °C. That's why its darks never quite match: the temperature keeps moving while you shoot.

Heads-up, DSLR shooters: the camera heats itself up. They start out at air temperature, but the electronics and the long exposures push the sensor up 4 to 6 °C over a run, and the noise with it.

Go for slightly shorter subs with a gap between them, which you can set on your intervalometer: 60 s on, 15 s off, say. And put the camera outside half an hour before you start, so it settles at the outdoor temperature: if it's 25 °C indoors and 15 °C out, your first subs won't match anything.

The trick: darks on a cloudy night. Wait for a cloudy night at about the temperature of your session and run the same sequence with the cap on (and the viewfinder covered): same exposure, same ISO, same gaps. The sensor climbs the same way (18 to 24 °C, for instance) and the darks match almost sub for sub. You don't burn a clear night, and you build a library by temperature.

Canon bodies record the camera temperature in every frame. To stack, in ASTAP (free) check Classify by › Dark temperature on the stack tab and set the tolerance, ±3 °C for instance. ASTAP then matches each light to the darks shot at its temperature. No sorting by hand. See the ASTAP documentation.

A bit of backstory. That checkbox exists because of one summer night. When I was starting out I shot with a Canon EOS R in Seville, where summer nights hover around 30 °C, and my darks never matched my lights. I pitched the idea to Han Kleijn, the author of ASTAP. He liked it and added it. Thanks, Han.

Fran López, who builds Astrolarius
A simulated 5-minute dark

The cheat sheet

  • Darks

    20 to 50

    Redo them
    When the exposure, the gain or the offset changes (the ISO, on a DSLR), or the sensor temperature does.
    They depend on
    The camera, not the scope.
  • Flats

    20 to 30 per filter

    Redo them
    When you rotate the camera, refocus, swap filters or pick up new dust.
    They depend on
    The whole optical train.
  • Dark flats

    As many as your flats

    Redo them
    When the flat exposure changes.
    They depend on
    The camera.
  • Bias

    30 to 50

    Redo them
    Almost never: they keep for months.
    They depend on
    The camera. Mostly useful on a DSLR.

More calibration frames mean less noise in the final image, but past 50 you barely notice. Your Bortle class and your target change nothing: calibration is about your camera and your optics, not about the sky.

Quick answers

How many dark frames do I need?
20 to 50. Redo them when the exposure, the gain or the offset changes (the ISO, on a DSLR), or when the sensor temperature does. With a cooled camera at a fixed setpoint, a library keeps for months.
Do I need to take flats every night?
Flats depend on the whole optical train, so you need new ones whenever you rotate the camera, refocus, swap filters or pick up new dust. If nothing moved, your last set will do — but shooting them every session is the safe bet.
Do I need both bias frames and dark flats?
With a dedicated CMOS camera, no: dark flats are more reliable than bias. On a DSLR it's the other way around: the bias frames do that job, and they keep for months.

Shooting from a tripod instead? The exposure calculator gives you the seconds per sub, and the field of view calculator shows how your gear frames the target. The full guide to calibration is in Spanish for now: Calibración: darks, flats, bias y dark flats.